Beachcomber 538 Instruções de Operação descarregar pdf (Página 10)

START UP

When your hot tub is ﬁrst activated, it will go into priming mode (after

displaying some conﬁguration information). The priming mode will last

up to 4 minutes; then circulation will start, then heat icon will come on

for 6 seconds, and then ﬂicker for 90 seconds. Then heater will come

on to heat water to set temperature. It is recommended that priming

mode be allowed to ﬁnish, preventing any pumps from operating dry. If

you are positive all pumps are primed you can exit priming mode early

by pressing or .

TEMPERATURE ADJUSTMENT

Temp range is: (80°F - 104°F/26.0°C – 40.0°C) The factory pre-set

temperature is set at 100°F/37.5°C. The last measured temperature

is constantly displayed on the LCD. See edit menu in Owner’s Guide

to select F° or C°.

Note: On non HushPump™ hot tubs the

current water temperature will only be displayed if the 2

speed ﬁlter pump has been running for two minutes.

WARM / COOL

Press the or button twice to display the set temperature.

Each time either button is pressed again, the set temperature will increase

or decrease depending on which button is pressed. After three seconds,

the LCD will automatically display the last measured water temperature.

HEATING MODES

This button is used to switch between Standard, Economy, and Sleep

modes. Press to enter mode programming, press to cycle

through to desired mode (LCD ﬂashes until conﬁrmed), then press

to conﬁrm selection.

Standard Mode

maintains the set temperature at all times. Note

that the last measured hot tub temperature displayed is current

only when the pump has been running for at least 2 minutes. The

STANDARD icon will display until the mode is changed.

Economy Mode

heats the hot tub to the set temperature only during

ﬁlter cycles. The ECONOMY icon will display until mode is changed.

Pressing 1 while in Economy mode puts the hot tub in

Standard-In-Economy mode, which operates the same as Standard

Mode, then reverts to Economy Mode automatically after 1 hour.

Use this mode to activate the heater if using the hot tub when not in

ﬁlter cycle. During this time, a press of the button will revert to

Economy Mode immediately

Sleep Mode heats the hot tub within 20°F (11°C) of the set

temperature only during ﬁlter cycles. The SLEEP icon will display until

mode is changed. Use this mode when going on holidays.

MASSAGE 1

Press 1 button once to turn pump 1 on to low speed, press

1 again for the pump’s high speed, and once more to turn off the pump.

Low speed turns off automatically after 2 hours and high speed turns

off automatically after 15 minutes. Massage pump 1 comes on for a 1

minute purge at the start of each ﬁlter cycle.

MASSAGE 2

Press 2 button once to turn pump 2 on to low speed, press

2 again for the pump’s high speed, and once more to turn off the pump.

Low speed and high speed turn off automatically after 15 minutes.

Massage pump 2 comes on for a 1 minute purge at the start of each

ﬁlter cycle.

TURBO(optional)

Press the button to turn Turbo on and off. Turbo will

automatically turn off after 15 minutes. Turbo comes on for a 10

second purge at the start of each ﬁlter cycle.

LIGHT

Press the button to turn the hot tub light on, press again to turn

off. Light will automatically turn off after 3 hours.

STANDBY MODE

Pressing or followed by

will turn off all hot tub

functions temporarily. SBY will appear on your display.

This is helpful

when changing a Microﬁlter cartridge. Press any button to exit standby

mode. Note: If hot tub is in a heat cycle when standby is selected the 2

speed pump or HushPump™ will run for approximately 15 seconds.

ET-7 CONTROL PANEL INSTRUCTIONS

TurboLightWarm

Cool Massage1 2

Time

Mode/Prog

TurboLightWarm

Cool Massage1 2

Time

Mode/Prog

TurboLightWarm

Cool Massage1 2

Time

Mode/Prog

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Comentários a estes Manuais

Sem comentários

Beachcomber 538 Instruções de Operação Página 10

Comentários a estes Manuais